Belt dryer is widely-used continuous drying equipment, which is consisted of feeding device, one or several drying chambers. Raw material is spread on belt conveyor and hot air will pass through the raw materials from up to lower or bottom-up. In this way the raw material can be dried uniformly. Each chamber is equipped with main chamber, drive system, heating system, hot air recycle fan, and dehumidifying system. According to abundant experiences and new technology, we improved the traditional belt dryer to meet the GMP standard and meet the requirements of different raw materials.
The hot air goes through the material from up to lower or bottom-up, with high speed, high pressure and even distribution, the contacting area between the material and hot air is enlarged, and the drying speed gets improved. The heat source is gas indirect furnace. The hot air box is below the recycle fan. There are hot air distributing pipe outside the chamber, so that the hot air can sprayed evenly from the retaining plate, the advantages of this structure are: The drying temp is easy to be controlled, which is significant for various material drying process; The hot air is sprayed through retaining plate, which made the temperature evenly and can avoid partial high temperature No maintenance for hot air box, the hot air box is inner set and outside preservation, which can minimize heat loss There are air filter for the exhaust fan, frequently cleaning can avoid miscellany and pollution. The dehumidifying fan is above the feeding device, which is used for discharging the used high-moisture and low-temp air. The hot air is recycling from discharging section to feeding section, so as to save energy effectively. The whole equipment is full weld to avoid wind channeling. There is no leaking during cleaning, which can ensure the quality of final product. Fully-closed model is available, to make sure that the product will not be polluted and heat is high efficient. The access door makes the maintain and cleaning work convenient The DW is a energy-saving belt dryer. The air distribution is more even, hot air speed is higher, penetrating is effective, drying is more strength. This system is inner recycle type; primary selection is DW3-2-25, including 12 drying units, for each section, there is thermal resistance automatic control independent and with digital show. All key components are provided by famous manufacturer, which can ensure long-term operation of the equipment. The belt speed can be electromagnetic adjusted, and the adjust range is large, besides, the speed can be directly displayed on the control cabinet screen, so that the final moisture can be controlled effectively. Primary and Middle Filter can ensure the clean air inlet All recycle fans are centrifugal, which are low consumption, high pressure and high penetration rate.
Name | SPEC | Material | QTY |
Mainframe System | |||
frame | 60×80 | Carbon steel | 1set |
Mainframe | DW3-1.5×25 | SUS304 belt | 1set |
Insulation thickness | 60mm | Glass wool | 1set |
Dehumidify fan | 4-72-6A4.0kW | C.S | 12pc |
Circulating fan | 4-72-5A2.2kW | C.S | 5pc |
Reduction gears of belt | 0.75 kW | assembly | 2pc |
Transmission shaft | 45# | 6pc | |
Belt chain wheel | Z=10,P=76.2 | 45# | 12pc |
Link chain | P=76.2 | Carbon steel | 300m |
Belt | 8 mesh | SUS304 | 157m |
Striker plate | H100mm, δ1.2 | SUS304 | 3950 |
Belt stay bar | Out 23, in15 | Zinc coat | 990 |
Belt, chain, wheel | Carbon steel | Zinc coat | 3 set |
mounted bearings | UCK210 | assembly | 12set |
Gate lock door hinge | assembly | Whole set | |
Sealing strip | E | Silicon rubber | |
thermal resistance | Pt100 | assembly | 18set |
Belt tighten device | Carbon steel | 6set | |
Dehumidify duct | Zinc coat | 5set | |
Inlet air duct | Zinc coat | 1 set | |
Heating System | |||
burner | RS100 | 1 set | |
Gas fuel furnace | 100×104kcal/h | Inside SUS304 | 1 set |
Air blower | 4-72-8C-30kW | ||
Control System | |||
Control cabinet | button | 1 set | |
Electrical element | 1 set |
Pre-Sales Service
* Inquiry and consulting support.
* Sample testing support.
* View our Factory.
After-Sales Service
* Training how to install the machine, training how to use the machine.
* Engineers available to service machinery overseas.
Q: What does Better need from me to quote a price?
1.Raw material
2.Production capacity per batch
Q: How long does it take to produce the machine once I place my order?
Usually, the delivery time is 30 working days after prepayment received.
Q: What is the minimum quantity I must order?
We don't technically have minimums, but if you order more than 3 sets once,we can give you a discount.
Q: Do you have machines in stock?
No, our machine is produced according to your request.
Q: How will my order be packed, can you provide the installation service?
Packed in plywood case.
Miss Joyce:
---Your professional sales manager
Tel: +86-18917686969
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.